Blog

• This means that vinyl has a better moisture resistance than laminate because the plastic is 100% impervious to moisture. Laminate flooring can also be very moisture resistant as long as the planks are properly connected–although not 100% like with vinyl.

Flooring is typically installed in the same direction of your leading source of natural light, and the same goes for luxury vinyl. If you have large windows in a living room or an entryway that allows a flood of natural light, then run your planks in the same direction.Aug 10, 2020

Vinyl flooring is strong and stable on its own, but staggering can add to the floor's structural strength. Racking the planks also improves the floor's aesthetic appeal. The trick to stagger vinyl plank flooring successfully is to play around with the minimum spacing and laying down the planks randomly.

In the same vein, it's typically recommended that planks are installed parallel to the longest wall of the room. So, if you're installing vinyl planks in a 12 foot by 18 foot living room, run the planks parallel to the 18 foot wall. This will make smaller rooms feel bigger and wider.

1 Answer. Use a circular saw with a wood cutting blade set to the depth of the vinyl floor thickness. Osc tools are invaluable for small jobs but they are slow and you'll burn through a lot of blades to cut something that size out.

The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.

A miter saw is a great tool for cutting vinyl flooring. You can slice the pieces of flooring quite easily. It gives a clean and flawless finish due to straight edges, unlike some other saws. It also can easily cut at an angle, which is probably its most well-known feature.

You can use a circular saw if you'd like, but the base plate is probably too big for a standard vinyl plank. Circular saws also have issues with kickback when working with thinner materials. Wood-cutting circular saws also can't use metal-cutting blades, which is a problem for some vinyl planks.

1 Answer. Use a circular saw with a wood cutting blade set to the depth of the vinyl floor thickness. Osc tools are invaluable for small jobs but they are slow and you'll burn through a lot of blades to cut something that size out.

• Best Vinyl Plank Flooring for Your Home Home Depot LifeProof Vinyl Plank Flooring. Home Depot tends to be at the forefront of economically priced home products, including floor coverings. Shaw Resilient Vinyl Flooring. ... Armstrong Luxe Plank: Vivero. ... Mannington Adura Rigid Plank. ... Lumber Liquidators CoreLuxe Ultra. ... Karndean Luxury Vinyl Plank Flooring. ...

• The USCutter MH-Series are the best value vinyl cutters available anywhere! Works with VinylMaster Cut and other popular software (like Sure Cuts Alot, Flexi , SignBlaser and SignCut Productivity Pro) through standard vinyl cutter PNC1000 drivers.

• Utility Knife or Scoring Tool: Vinyl siding is easy to cut and a utility knife or scoring tool can be used to trim and score the material. Always remember to score the vinyl face up, apply medium pressure and carefully snap it in half.

• Laying tile over vinyl flooring on a plywood subfloor: Apply thin-set adhesive to the vinyl flooring with a notched trowel. Screw or nail 1/2″ cement backer board on top of the vinyl while the adhesive is still wet. Apply thin-set adhesive to any joints in the backer board. Embed fiberglass mesh tape over the joints in the adhesive.

• Vinyl flooring can be cut by means of a utility knife pulled slowly across the top. If you notice that the material is starting to become harder, reheat it. Always make sure that you cut less than what you are supposed to remove. If you overcut, there will be gaps in the area where you are going to lay the material.

• Home Depot LifeProof Vinyl Plank Flooring. Home Depot tends to be at the forefront of economically priced home products,including floor coverings.
• Shaw Resilient Vinyl Flooring. ...
• Armstrong Luxe Plank: Vivero. ...
• Mannington Adura Rigid Plank. ...
• Lumber Liquidators CoreLuxe Ultra. ...
• Karndean Luxury Vinyl Plank Flooring. ...

• 1) Measure in from the side near both ends of the plank, and make a small mark where the cut will be made. ... 2) Lay your level along the plank to connect the small marks. Use the pen to make a cut line. ... 3) Use the straight edge as your guide to score the plank. And then snap it along the cut line and remove the scrap.

Cutting your planks into a special shape should not have to be a problem. Cut the shape into the vinyl plank – making sure that the cuts will fit snugly – and break this shape out of the plank. Pro Tip: Always place an extra plank upside down underneath the plank you want to cut.

Score and snap is the basic technique, but it must be applied in three different ways: Crosscuts are short cuts across the plank. Rip cuts are long cuts down the length of the plank. Notch cuts remove small pieces to fit flooring around door jambs, pipes and similar. These cuts make the plank shorter.

They are made on planks as you complete a row and as you cut planks to stagger vinyl plank flooring. Step 1. Measure and mark the plank on the waste side of the cut line.

A regular utility knife blade can be used to cut flexible, self-adhering laminate strip material. The caveat is that you must change the blades frequently so the knife cuts properly -- a dull blade will not cut effectively.

• Vinyl tile can be cut with a razor knife, but that is hard work. It is best to use a vinyl tile cutter. These devices can be rented at tool centers. They are hand operated and make very crisp cuts.

• Many different types of vinyl flooring can easily be installed over hardwood, from floating vinyl planks over hardwood floors and other types of vinyl flooring over hardwood. The key is simply to select a product that doesn't need to be glued, stapled, or nailed to the hardwood subfloor.

• While self-stick vinyl tile is generally used on floors, you can use it to dress up a wall in most rooms and enhance your home decor. Just keep in mind that the joints in between the tiles aren’t waterproof, making the vinyl tiles a poor choice for bathrooms and other areas with moisture.

Time to cut your vinyl plank flooring! The technique you’ll need to use will depend on the direction of the cut you need to make. If you’re going to shorten your vinyl plank, you can use the scoring technique. You’ll often need to do this to fit in a plank at the end of a row. But you may also need to reduce the width of your plank.

These cuts make the plank shorter. They are made on planks as you complete a row and as you cut planks to stagger vinyl plank flooring. Step 1. Measure and mark the plank on the waste side of the cut line. Step 2. Place the plank on a surface you won’t mind cutting on such as the subfloor or a piece of waste flooring with the bottom side up.

Once you’ve cut the tongues, you should lay the first row with the cut side facing the wall. Also, carefully place the vinyl planks to keep an even expansion gap between them and the wall. Your first plank is down.

Step 1. Measure in from the side near both ends of the plank, and make a small mark where the cut will be made. Again, remember to make your mark on the scrap side of the plank, the piece to be trimmed away.

Time to cut your vinyl plank flooring!

Use the score-and-snap method for cutting along shorter lines, and a jigsaw for longer cuts. And whatever method you're using, make sure you double check your measurements first. You won't be able to stick your planks back together if you make a mistake.

Vinyl plank flooring usually comes in pre-cut sections, but you'll likely need to cut some of it yourself to match it to the specific dimensions of your room. ... Scoring and snapping is the preferred method for smaller pieces, while a jigsaw will come in handy when it comes time to cut lengthwise.

Problems related to vinyl plank flooring include being prone to discoloration, stains, scratches, peeling, cracking, and crumbling at the edges. There are also certain installation-related failures that you need to watch out for. These include curling, warping, peaking, and mold and mildew.

• Any strong carpenter's wood glue works for gluing vinyl to wood. Carpenter's glue is available for indoor and outdoor use, so choose the one that corresponds with where the finished project will go. Spread glue on both the vinyl and the wood, and press the two together. Wipe away any excess that squishes out.

• - Use the utility knife to cut straight down the middle of your vinyl floor. - Next, move about 12 inches to the right or left and cut a strip parallel to the first. Cutting in narrow strips makes the task more manageable. - Roll the vinyl as you make your way down the length of the strip. - Once it's cut, gently lift the strip of vinyl until you encounter resistance from the glue near the perimeter. - Use a 5-in-1 scraper to loosen the vinyl. If it doesn't come off, you will need to use the prybar and hammer to chip at the hardened adhesive. - For vinyl plank flooring or vinyl tile flooring, pry up a corner of one of the tiles with a putty knife. ...

• The best way to cut laminate flooring is to buy a laminate flooring saw, as it is designed to perform this task. This tool comes at a high price, as it is a professional saw for cutting and installing laminate flooring on large surfaces. Make Straight Cuts.

• Circular Saw. You can easily cut laminate plank material like any hardwood flooring with the help of circular saw right along the length of the piece with a power miter saw to cut off the ends. Always use carbide-tipped blade specifically rated specifically for use with laminate material.

• Measure the length and width of the room or rooms where you plan to install the laminate flooring. For accuracy, you should measure twice. Multiply the room's length by its width to calculate the total square footage of the floor.

• You can lay the flooring in a 10-by-20-foot bedroom or living room in two or three hours, but you should add an hour or two to fit it around cabinets or other obstacles in a kitchen or bathroom, depending on your skill with power tools.

Most vinyl plank flooring kits come with innocuous looking plastic spacers. The instructions recommend the use of spacers but I don't think they properly communicate the necessity of their use. The spacers are used to fill the gap between the baseboards (which should be removed) and your newly laid floor.Jan 31, 2019

• Vinyl tile can be cut with a razor knife, but that is hard work. It is best to use a vinyl tile cutter. These devices can be rented at tool centers. They are hand operated and make very crisp cuts.

• Since laminate floors have a wood based core, liquid spills should be wiped promptly. LVT vinyl planks are inherently water resistant and can be wet mopped. LVT is clearly a better choice in wet areas.

• Measure Twice,Cut Once. Good preparation is the key to success when you are installing vinyl plank flooring. ...
• Making the First Cut. Now that all of your measurements are down and your floor is clean,except for the chalk lines of course,it’s time to cut.
• Determine How Wide the Last Row Is. This should be the first cut you make. Determine the width of the last row of vinyl plank flooring. ...
• Getting the First Row Down. You need to remove the tongue from the plank. The easiest way to do this is by using a utility knife.
• Putting the Planks in Place. Your first plank is down. Take the second one,put it at a slight angle against the first,and fold gently until they click into ...
• Finishing Off the Rows. To fit the last piece you can score it using a utility knife and break off the excess piece. ...
• The Second Row and Beyond. Remember,you have to stagger the joints at 6 inches,at least. Measuring the first piece is very important.
• Connecting the Planks. The tongue of the first piece goes into the groove of the previous one and gently rotates until they click together.
• Doorjambs and the Finish. Get the vinyl planks under the doorjambs,as this provides an even fit of your flooring. ...
• The Final Cut. We hope you now feel confident enough to start cutting and installing vinyl plank flooring. ...

The most common way to lay hardwood flooring is by aligning the planks parallel to the longest wall. Apart from a few exceptions like sagging joists, this is the preferred direction to lay wood floors because it aesthetically provides the best result.

Rip cuts are long cuts down the length of the plank. Notch cuts remove small pieces to fit flooring around door jambs, pipes and similar. These cuts make the plank shorter. They are made on planks as you complete a row and as you cut planks to stagger vinyl plank flooring.

A miter saw is a great tool for cutting vinyl flooring. You can slice the pieces of flooring quite easily. It gives a clean and flawless finish due to straight edges, unlike some other saws. ... Using a miter saw is simple – you just need to make accurate cut marks.